My rental space rent went up again... Just can't do it any longer. Got to move before mid February just can't cram it all in the house garage.
Things that need new homes.
74 montesa cota 123 trials bike. OE manual and few other NOS parts was sold.....never paid for or picked up $400
Lincoln LincWeld 225 DC Arc welder with AC power outlet 3000w max 50hz. Opposed twin cylinder Briggs an Straton with electric start. No exhaust! I've never used to weld but have run it once. $200 or best offer
Pile of 74-76 360-390 Husky's easily make two bikes and have tons of parts left over. $600
62 Dodge Dart 440 trim package model 4 door slant 6 push button trans. Needs work but runs and drives well it did 8 years ago when parked inside. Make offer!
67-68 Plymouth Barracuda notch back OEM rear tinted glass. $50
67-68 Plymouth Barracuda Floor shifter with trans hump.
67-68 Plymouth Barracuda set of 4 hub caps
Mopar fine spine 4 speed "Hemi" trans with Hurst factory shifter, Bell housing, inspection pan, flywheel, clutch fork, NOS pivot ball and clips rubber cover. $200
Ford RAD four speed overdrive trans set up. Pulled from early 80's 3/4 ton work van. Trans, bell housing, New pressure plate, New clutch disk, OEM drive shaft, OEM shifter missing knob..it's here some where... $150
Delta truck box from Ford Ranger no lock key. $20
Bolt on electric hoist swivel crane. ~7ft reach, uses cable winch powerful HD unit. Needs a bit of wiring for up and down switches. $150
Wade "74" 6 position turret lathe with chip tray an flood coolant, 5C collate system and several chucks, tap heads and more tooling. $1000
Flathers and Sons 6 ft lathe. Made in Nashua NH late 1880-1940's gear box type change gear, overhead drive "drive all" 4 speed gear box. $200
Light Machine corp brand Spectra Lite model (Manchester NH) mini CNC lathe with control box. No idea if it works or what programs it uses / interfaces. $100 Just talked with a guy at the factory. They still make this unit! $9000 with no options or tooling just bare unit! He said by its age it would need an ISA interface card and a computer running windows 98 no newer then ver 2. He has refurb card for $650 He said the interface box could be upgreaded to the newer unit but thats $3500 The box is 25 inches wide motor stickes out another 5inches or so. It has a 3 inch 3 jaw chuck with two sets of jaws several tool holder (5 i think) tail stock with center.
I'll get Pictures dumped soon.
Van Norman LARGE 303 Senior Brake Drum lathe with finish grinder. Several arbors and adapters to allow flywheel grinding. Made in Springfield Mass! $200
Airco 400 AC/DC "Bumble Bee" welder. 220v single phase input no output leads (used them on another welder) on wheels $150
55gal drum / Motorcycle lift. Originally a 55 Gallon drum lift. Air powered hydraulic pump. drum strap and tilt unit was removed and a HD table fitted. will lift any bike over 6ft high. Nice when you need to do things like clean the underside. Have drum tilt unit somewhere. $150
Motorcycle Chassis DYNO! Patraco brand water brake type with ~10 inch drum, 150 wheel HP unit, originally fitted with heat exchanger on the cooling loop OE exchanger busted have replacement unit. Never used this dyno, got it and bought parts to fix it never had space to use it. Rumored to have come from SKY cycle in the 70's. $500
Chevy 305 short block. Worn #7 cyl cam lobe (like most 80's 305's) have heads but are apart for valve job. no intake or distributor. $100
Chevy 283 Short block. STD bore! Early unit 57 or 58 has canister oil filter. one piston has dome damage from nut dropped down the carb while running (not me) $350
78 Camaro truck lid with spoiler and quarter ends $50
78 Camaro Tail lights crazed but whole units with rear wire harness. $50
Hooker exhaust kit part #16562 65–76 Ford F100/250(2WD), 67–75 F350 (2WD): 352–390, 2.25 OD tubing Dual Competition Header Back Exhaust System Kit all pipes have Aluminized factory finish and top coated painted with high heat alum paint. all clamps and hangers etc full kit never installed Paid $170 + shipping Asking $100
68 Hornet Marauder II enduro go kart. Has 69 update rear flex frame. former Nat title holder drum front brakes disk rear dual 5 gallon side pods Mac Mc9 motor set up to run on 5% nitro methanol last raced 1970 at Buffalo lakes TX motor was rebuilt by Van Glider and stored untill mid 90's run a few time. FASR KART no place to drive localy. Crap load of spares. $1500
70's yard kart brand unknown Mac MC91 powered rejeted to run on gas fast and fun kart. $400
Make offers!! Will trade for storage units like box trucks or shipping containers, 74 yamaha MX or DT bikes, Rickman motorcycle (both Zundap and Montesa powerd)
