1986 CRX Si Ex-autocrosser Rolling tub with goodies

Unfortunately the motor blew this last weekend on the car, so here's what is left. Could make the nice beginnings of a challenge car!

Drivetrain: Non-running 1987 Acura Integra D16a1 Engine and transmission swap – hole in front block where a connecting rod came through. Lightened flywheel Short shifter AC and most emissions equipment removed DC Sports Ceramic-coated 4-2-1 Header K&N Cold Air Intake Cat-less custom exhaust by Frank Hoerdemann at Mytee Muffler, Peoria

BRAKES 87 Integra front and rear brakes (new rotors and rebuilt calipers last year) Porterfield R4 Competition brake pads (all 4 corners) with 3/4 pad left. May need new front pads, as the engine failure sprayed oil all over the driver’s side. Stainless braided brake lines Freshly flushed brake fluid (Brembo Racing LCF600+)

SUSPENSION 23mm front torsion bars, Integra front sway bar and internal rear sway bar Full Energy Suspension Hyperflex bushing kit Tokicko Illumina 5-way adjustable shocks front and rear Ground Control adjustable rear spring collars Eibach rear springs Front struts lowered in the bottom suspension knuckles for increased travel David Braley billet front camber plates Competition alignment by Wade at Terry Wynn

MISC. Battery relocated to rear of car Autometer oil pressure and water temp gauges Dash-mounted fire extinguisher

Wheels: 14"X6" Volkswagen "teardrop" aluminum wheels with OLD BFGoodrich R1 race tires mounted for rolling the car. Not recommended that these tires be used for anything other than supporting the car while it is rolled. Wheels are in decent shape though

Also included: Original Si engine and transmission, axles Most of the original interior and original driver's seat (driver’s seat mounts will need to be fabricated as they were cut out to previously mount a race seat)

Asking $700 O.B.O. Located in East Peoria Illinois. I'm willing to deliver the car within a 100 mile radius of Peoria to the new owner. shepherdsfold@comcast.net

Now with pics: NOTE: Cage has been removed and is for sale separately below Close-up of camber plates:

TOO_MANY_1ST_GENS. MUST_COMPLETE_PROJECTS. BALLS_IN_JEOPARDY. E36 M3. Let me know if it's still around in a month. Are you anywhere near 16VCorey?

dunno 16vcorey. Where's he located?

DOH! Indiana (not Illinois.) Nevermind.

poopshovel wrote: DOH! Indiana (not Illinois.) Nevermind.

The border of Indiana is only a couple hours from me. If you have serious interest in the car we could probably work something out. :-)

He's in Evansville (5 hours away?) Again, if it's around in a month or so let me know - or let me know if you're willing to split stuff up. Mamma is less likely to notice 'pieces' than 'cars.' I'm mostly interested in the suspension, specifically the T-bars, the integra trans., and exhaust. Is the clutch any good?

Cool website, BTW.

Will do. I'm hoping to be rid of it in less time than that though. Clutch was in good shape before the engine let go.. I assume it's still alright, but I haven't driven it since.

BTW - I also have a Kirk 6-point roll cage and a suspension techniques external rear sway bar I'll be advertising here in a bit as well for the same car.

nynone4 wrote: ...BTW - I also have a Kirk 6-point roll cage and a suspension techniques external rear sway bar I'll be advertising here in a bit as well for the same car.

I would be interested in that roll cage

Here's the roll cage from the car - for sale separately. I believe it's an older kirk bolt-in cage. It's all in primer, and includes the backing plates and bolts. Never "tested."

$225 OBO. Local pickup in Peoria, Illinois please - this thing would be a beast to ship!

Cage as it looked in the car before removal:

Cage as it sits now in the garage:

too many awesome CRX's for sale lately...

wanna trade?

http://grassrootsmotorsports.com/forum/2008-classifieds/84-e-prepared-crx-1000-ready-to-race-not-a-project/4981/page1/

savestheday wrote: wanna trade? http://grassrootsmotorsports.com/forum/2008-classifieds/84-e-prepared-crx-1000-ready-to-race-not-a-project/4981/page1/

No thanks. I've found a replacement car and need the funds to put towards that. Good luck with your sale!

Thats the cage I needed for Lemon's last July. Hell of a deal on the cage1

Bump... anyone need a project car?

SOLD! (both the cage and car). Thanks Bill!

Thanks Matt

Bill