chevy 350 2 bolt main 3970010 block, std bore with caps $50
1991 chevy 4L80-e transmission no converter SOLD
3 speed manual trans with bellhousing appears to be from a 67-72 c10(mounts on bellhousing not on tail) $40
new old stock gm flywheel, think it's for a 454 but i will get part # $50
rebuilt 4.3 vortec heads with about 20 minutes run time with composite valve covers, rockers, pushrods $100 take whole engine with new timing set and new crank kit but a knock for $125
95 s10 aluminum wheels(swept wide 5 spoke style) with center caps and crap tires $75
full low mile set of bilsteins off a '10 durango $90
tractor supply crossover diamondplate toolbox for fullsize truck $50
LSx truck oil pan, windage tray, pickup tube $65
LSx truck (2001 5.3) intake/rails/injectors under 40k $50
beer kegs - 2. i older barrel style one newer style. make a stainless gas tank. $25 each
old school red jerry can $20
all parts located near cleveland ohio, will ship smaller stuff. i am going to keep adding to the list as i clean stuff out. i have some awesome small block headers that i don't think i can ever use that i'm going to post pics of too.
keg. list of wants but not something i need in the slightest
Pat,
What condition is the 4l80E in?
You are too far away. Boo.
Damn. A keg and a toolbox are probably prohibitive to ship.
they are definitely prohibitive to ship but where in PA are you? if you are along the route from cleveland to baltimore or cumberland it could work.
the 4L80-e is unknown. i bought at pull a part, the engine was locked solid so i assume the bad engine is the reason the truck got junked and pulled the trans assuming it would be good. but i have it priced under the assumption it is a rebuildable core. the fluid did not smell toasty. i personally would bolt it in and see what happens just based on the truck i pulled it from knowing the engine was bad.
I am 2hrs up i81 from Cumberland. How often are you out this way? I might be attending a Porsche swap meet in Hershey next Saturday (which is right in the ballpark give/take 20 miles.
dug out 93-97 camaro gauge cluster(full gauges/tach/110 speedo) from v6 car for $20
16x7 american racing 7 spoke wheels in 5x115(gm fwd) bolt pattern for $75/all 4.
4 original steel wheels for mid 70s international scout $40
73-80 chevy grill ends/headlight surround pieces $20
73-81 chevy/gmc aftermarket door shells no rust but 6x9 speaker cutouts down low $100
89-91 suburban/k5 core support brand new still wrapped up $75
unknown 7.5" 10 bolt s10 rear axle $25
06-10 explorer rancho 1.5" lift rear pair of shocks with springs and top mounts brand new $150
studebaker v8 center bolt valve covers(fit center bolt small block chevy engines with a little tweaking to make them look not new) $75
82-93 s10 rear step bumper, bent on right end but no rust so if you need a cheap way to tow with your s-truck.... $10(scrap price) with 2" trailer ball
99 p71 black grill $10
early 00's-'10's overland big truck radiator and shell. rad needs repair around top inlet. i hate the term but this is "rat rod" type stuff. $50
39-40 chevy/gmc headlights with stands $200
patgizz wrote:
they are definitely prohibitive to ship but where in PA are you? if you are along the route from cleveland to baltimore or cumberland it could work.
the 4L80-e is unknown. i bought at pull a part, the engine was locked solid so i assume the bad engine is the reason the truck got junked and pulled the trans assuming it would be good. but i have it priced under the assumption it is a rebuildable core. the fluid did not smell toasty. i personally would bolt it in and see what happens just based on the truck i pulled it from knowing the engine was bad.
Consider it sold. We'll have to figure out the details.
the 4l80 is in my dad's garage in medina, i can meet you there or get it to my house so you can check out all my junk. he's 5 minutes from me tops. i'm about 35-40 minutes from you. whatever works for you. i'm just turning around and buying a new auto-x helmet with the money.
things i will use $ for if someone has any of them in trade
1 pair 1.25" thick 5x4.75 to 4x4.5 wheel adapters
complete rust/dent free front clip for 91 sonoma
wiper motor with delay for same sonoma
bump, adding more this weekend.
6 lug 17" gm wheel with decent tire, looks like newer stuff like silverado or trailblazer. black aluminum wheel. good spare? $20
49-54 chevy/pontiac under floor power brake pedal and booster mount from speedway motors, new. $50
73-87 chevy vent window assemblies $30/both
73-80 chevy/gmc grill ends(headlight surround parts) $20/both
stock s10 spindles $10
s10 big brake kit - adapters, used 4th gen lt1 front calipers and rotors. need to have stock rotors machined into hubs and do a little work on your spindles - chop off factory caliper mounts and drill out/tap 2 backing plate holes for adapter brackets. $150
stock s10 rear springs in excellent condition, carried 1000+lb while sitting level. $50
fox body lincoln rear sway bar $10
95 impala ss rear lower control arms with sway bar mounts - sell complete arms or just sway bar mounts and bolts for $30, add rear sway bar to any 77-96 b or d body.
I will be in Akron this weekend, are you available?
I'll take a keg. Feel free to cut the top off for me. I need a home brew boiler.
Is the unknown axle unknown in lineage or just unknown in gear ratio?
unknown year and ratio, only know its from an s10. it was under my 40 chevy truck bolted rather poorly to the original springs when i bought the truck. i know that it rolls and nothing sounds bad when i spin the yoke. hence scrap pricing.
4L80-e sold, most of the rest of the prices dropped
I want that 3-speed... as if my C-10 didn't get bad enough fuel economy.
I'm the wrong direction from PA though.
drop to 50 if you want them andy. i honestly forget what i paid but i know i've seen them on the hamb before for 100-125. i'm not building anything where i feel the need to make a centerbolt small block look old.
JThw8
UberDork
5/4/12 10:10 p.m.
Just to fuel the fire for Andy here is an article on exactly what needs to be done to convert the Stude covers for a chevy centerbolt. If you right click >open you can view the photos, they don't seem to display in the thread anymore.
http://www.jalopyjournal.com/forum/showthread.php?t=332670
patgizz wrote:
drop to 50 if you want them andy. i honestly forget what i paid but i know i've seen them on the hamb before for 100-125. i'm not building anything where i feel the need to make a centerbolt small block look old.
I'm sure you saw the Off Topic thread. As much as I'd like them, I can't.
